Retient le Plug Inverse & le Ressort sur la Tige Guide lors du Démontage
Ce clip en acier pratique s'enfile sur une tige guide de pleine longueur et retient solidement le plug inverse et le ressort lors du démontage d'un 1911. Il agit comme une « troisième main » pour maintenir le ressort et le plug sur la tige pendant que tu retires ou installes la glissière. Cela élimine le besoin d'outils improvisés comme de petits clous ou des trombones qui peuvent tomber et causer un risque de sécurité en lançant de manière inattendue le ressort, le plug ou la tige à travers l'atelier.
CARACTÉRISTIQUES : Acier, environ 21⁄8" (5,4 cm) de long.
Plus...
Retains Reverse Plug & Spring On Guide Rod During Field Stripping
Handy steel clip slips over a full-length guide rod and securely retains the reverse plug and spring when field stripping a 1911. Acts like a “third hand” to keep the spring and plug on the rod while you remove or install the slide. Eliminates the need for improvised tools like small nails or paper clips that can fall out and cause a safety hazard by unexpectedly launching the spring, plug, or rod across the shop.
SPECS: Steel, approx. 21⁄8" (5.4cm) long.
Plus...
Évaluations client de COMPETITIVE EDGE DYNAMICS REVERSE PLUG RETENTION CLIP
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 3,5
Works well, though I have so many small hex wenches and small diameter wire accumulated on my bench over the past 32 years. Bought this out of interest alone and it is well designed and seems strong so I can't say anything negative for a simple tool.
Reverse Plug Retention Clip - Review(21/07/2016)
I bought this because cleaning my Wilson Combat Officer's model 1911 with a Reverse slide plug was a pain - the 'homemade pin' kept falling out. This part is a good concept, but required modification to work. 1st: the 'short' clip was still too long for an Officer's model I cut it and then re bent the end to work. 2nd: the original 'bend' length was way too short to function - at all. 3rd. The 'circle' diameter was too large for the slide rod. I bent it to a closer match. Once these 'mods' were done, the clip works well. It might work better on a Commander or full size 1911; but I strongly suspect the 'pin end' will need to be re bent for a longer length.
Référence: 100004616 COMPETITIVE EDGE DYNAMICS REVERSE PLUG RETENTION CLIP Ref Fabricant: 300033 Ce clip en acier pratique s'enfile sur une tige guide de pleine longueur et retient solidement le plug inverse et le ressort lors du démontage d'un 1911. Il agit comme une « troisième main » pour maintenir le ressort et le plug sur la tige pendant que tu retires ou installes la glissière. Cela élimine le besoin d'outils improvisés comme de petits clous ou des trombones qui peuvent tomber et causer un risque de sécurité en lançant de manière inattendue le ressort, le plug ou la tige à travers l'atelier.
Retient le Plug Inverse & le Ressort sur la Tige Guide lors du Démontage
Ce clip en acier pratique s'enfile sur une tige guide de pleine longueur et retient solidement le plug inverse et le ressort lors du démontage d'un 1911. Il agit comme une « troisième main » pour maintenir le ressort et le plug sur la tige pendant que tu retires ou installes la glissière. Cela élimine le besoin d'outils improvisés comme de petits clous ou des trombones qui peuvent tomber et causer un risque de sécurité en lançant de manière inattendue le ressort, le plug ou la tige à travers l'atelier.
CARACTÉRISTIQUES : Acier, environ 21⁄8" (5,4 cm) de long.
Plus...
Retains Reverse Plug & Spring On Guide Rod During Field Stripping
Handy steel clip slips over a full-length guide rod and securely retains the reverse plug and spring when field stripping a 1911. Acts like a “third hand” to keep the spring and plug on the rod while you remove or install the slide. Eliminates the need for improvised tools like small nails or paper clips that can fall out and cause a safety hazard by unexpectedly launching the spring, plug, or rod across the shop.
SPECS: Steel, approx. 21⁄8" (5.4cm) long.
Plus...
Évaluations client de COMPETITIVE EDGE DYNAMICS REVERSE PLUG RETENTION CLIP
Nombre d'évaluations: 2
De brownells.com: 2
Note moyenne: 3,5
Works well, though I have so many small hex wenches and small diameter wire accumulated on my bench over the past 32 years. Bought this out of interest alone and it is well designed and seems strong so I can't say anything negative for a simple tool.
Reverse Plug Retention Clip - Review(21/07/2016)
I bought this because cleaning my Wilson Combat Officer's model 1911 with a Reverse slide plug was a pain - the 'homemade pin' kept falling out. This part is a good concept, but required modification to work. 1st: the 'short' clip was still too long for an Officer's model I cut it and then re bent the end to work. 2nd: the original 'bend' length was way too short to function - at all. 3rd. The 'circle' diameter was too large for the slide rod. I bent it to a closer match. Once these 'mods' were done, the clip works well. It might work better on a Commander or full size 1911; but I strongly suspect the 'pin end' will need to be re bent for a longer length.