Votre panier est vide.

Panier

Aide et contact

Livraison standard gratuite pour les commandes de plus de 249 €

Politique de retour de 100 jours

Newsletter

Promotions

Plus de 300 000 clients - nous vous disons merci !

4,93/5 "Très bien" (1400+ avis)

40 000+ produits pour la chasse et le tir sportif

LITE MOUNT TECHNOLOGIES
3-RAIL PICATINNY SHOTGUN MOUNT

100002041

Se monte facilement sous le canon ; accepte les accessoires Picatinny

Ce support rigide en aluminium à trois rails te permet de fixer des accessoires picatinny tels que des lampes, des lasers et d'autres équipements tactiques à ton fusil de chasse. Il s'installe sur le tube de chargeur sans modifications de l'arme et peut accueillir jusqu'à trois accessoires. Son point de montage bas maintient les lampes et les lasers correctement alignés avec le modèle de tir et empêche toute interférence avec les organes de visée en fer. Il se fixe avec deux vis de serrage 8⁄32".

SPÉCIFICATIONS : aluminium 6061-T6, noir mat. 1-5⁄8" (4,2 cm) de long. 1" - S'adapte aux tubes de chargeur de fusils de chasse Winchester, Remington et FN.

Plus...

Mounts Easily Under Barrel; Accepts Picatinny Accessories

Rigid, aluminum, tri-rail mount lets you attach picatinny accessories such as lights, lasers, and other tactical equipment to your shotgun. Installs on the magazine tube without modifications to the gun, and will hold up to three attachments. Low mounting point keeps lights and lasers in proper alignment with the shot pattern and prevents interference with iron sights. Secures with two 8⁄32" clamping screws.

SPECS: 6061-T6 aluminum, matte black. 1-5⁄8" (4.2cm) long. 1" - Fits Winchester, Remington, and FN shotgun magazine tubes.

Plus...

Évaluations client de LITE MOUNT TECHNOLOGIES 1" 3-RAIL SHOTGUN MOUNT

Nombre d'évaluations: 8
De brownells.com: 8
Note moyenne: 4

Fits Benelli mag tube extension (26/02/2010)

I had to search a while to find an adapter for my Benelli M4 - the 1" I.D. adapters everyone else sells to fit Benelli's are too small. This one fits perfectly without crimping the tube. My only gripe is that you must have the correct hex wrench handy to remove it for thorough cleaning. That also means you will probably NOT want to lock-tite the threads. I'm not sure how they'd fix this short of some type of levered quick-connect, and that might cause problems with the fit. I haven't fired the shotgun enough yet to know if it will loosen, but so far so good.

Doesn't fit Remington Model 887 (08/11/2012)

I purchased the LITE MOUNT TECHNOLOGIES 26MM 3-RAIL SHOTGUN MOUNT for my new Remington 887 tactical shotgun even though the magazine tube measures 27.5MM in diameter. When I recieved it, it would not fit on the magazine tube since the split where the clamping screws are located are un-even meaning the that the inside diameter (I.D.) is not round. So I tighten the clamping screws so the ID would be as round as possible. Next I had to machine the I.D. to a larger size (27MM). The fit test show that I had to use the I.D. expander to fit it on the magazine tube and it finally did fit. The next problem was installing the barrel. The semi-circle barrel/magazine tube gap filler would not let the barrel mount, it was too thick for the gap between the barrel/magazine tube on the 887. I had to totally remove it. Finally the rail mount fit and was useable on the gun. I rated this product a 3 since it is well manufactured and would most likely fit and on a standard 870 which has smaller diameter magazine tubes and larger gaps between the barrel and magazine.

Works Great (19/09/2009)

This item works great and looks good too. Very nicely machined and finished.

Perfect Fit, Easily Installed (26/03/2011)

Ordering the correct ID for my magazine tube resulted in a quick and easy install on a Mossy 590. A drop of GunTite on the two screws and mount stays put so that a TLR1 slides right on and locks up securely. I've used different magazine rail mounts but this is by far the best made and easiest to use.

Exactly what I was looking for! (31/07/2018)

Exactly what I wanted in order to mount a flashlight and sling mount on my Moss 590 shotgun. I used a 1" scope ring to mount the flashlight to the side rail. No issues putting the mount onto the shotgun. Just unscrewed the cap, pulled the barrel up and slide the mount onto the magazine tube. Once I had it where I wanted, I tightened the two screw and I'm all set. I will add a bit of thread locker to the screw just to be on the safe side.

FNH SLP 18" 3" Magnum Police Shotguns (18/01/2010)

Although this is a great design and very good quality, it absolutely will not fit an FNH SLP shotgun magazine tube extention. FNH now makes a Tri-Rail extention. [...]

Didn't Work (09/02/2010)

The design of this mount looks nice and the construction is ok, but measure your magazine tube carefully. My tube is a standard 12 gauge magazine extension, which is approximately 1". However, when measured closely, my tube is .060" over 1". This mount won't work if your tube is even a fraction over 1" (I don't know if it will work if your tube is 1" because I didn't measure the inner diameter of the mount before using it and my tube is not perfectly 1"). The mount has a jack screw hole to spread it out to mount it on the magazine tube. I used this but had to spread it until the black coating started to crack. I then pounded the mount on the tube using a wood block. I was finally able to get it on, but it gouged the magazine tube. Worse, it had to be widened so much to get it on that the tightening screw holes don't line up anymore. I am going to have to remove it and throw it away, and all I'm left with is a damaged magazine tube.

GREAT PRODUCT! (13/11/2010)

PERFECT FIT ON A WINCHESTER 1300 DEFENDER. EASY TO INSTALL AND LOOKS GREAT WITH A TACTICAL LIGHT MOUNTED WITH
IT.

Lire 8 plus d'avis sur brownells.com

84.9 84.9 1 EUR

Référence: 100002041
LITE MOUNT TECHNOLOGIES 1" 3-RAIL SHOTGUN MOUNT
Ref Fabricant: NONE Ce support rigide en aluminium à trois rails te permet de fixer des accessoires picatinny tels que des lampes, des lasers et d'autres équipements tactiques à ton fusil de chasse. Il s'installe sur le tube de chargeur sans modifications de l'arme et peut accueillir jusqu'à trois accessoires. Son point de montage bas maintient les lampes et les lasers correctement alignés avec le modèle de tir et empêche toute interférence avec les organes de visée en fer. Il se fixe avec deux vis de serrage 8⁄32".

84.9 EUR 0 84,90 € *

Avertir lorsque l'article est disponible

Pas disponible.

Caractéristiques: Finition: Matte Noir Style: Montage Rail

Ajouter à la Liste d'Envies

Poser un question

Propriétés

Ajouter à la Liste d'Envies

Poser un question

Points forts

Support rigide en aluminium à trois rails pour fixer des accessoires Picatinny.
Se monte facilement sur le tube du chargeur sans modifications de l'arme.
Compatible avec les tubes de magasin de fusils de chasse Winchester, Remington et FN.

Caractéristiques

Finition: Matte Noir Style: Montage Rail Poids du colis: 0,091kg Hauteur d'expédition: 56mm Largeur d'expédition: 69mm Longueur d'expédition: 91mm

Détails de l'article

Fabriqué au USA

Opérateur économique responsable conformément au règlement de l'UE

Brownells France
Immeuble l'Horizon 3 Rue Jacques Constant Milleret
42000 Saint-Étienne
France
contact@brownells.fr

Améliore ton fusil de chasse avec le support 3-rail Picatinny en aluminium. Fixe facilement lampes et lasers 🔦 sans modifications!

Se monte facilement sous le canon ; accepte les accessoires Picatinny

SPÉCIFICATIONS : aluminium 6061-T6, noir mat. 1-5⁄8" (4,2 cm) de long. 1" - S'adapte aux tubes de chargeur de fusils de chasse Winchester, Remington et FN.

Plus...

Mounts Easily Under Barrel; Accepts Picatinny Accessories

SPECS: 6061-T6 aluminum, matte black. 1-5⁄8" (4.2cm) long. 1" - Fits Winchester, Remington, and FN shotgun magazine tubes.

Plus...

Évaluations client de LITE MOUNT TECHNOLOGIES 1" 3-RAIL SHOTGUN MOUNT

Nombre d'évaluations: 8
De brownells.com: 8
Note moyenne: 4

Fits Benelli mag tube extension (26/02/2010)

Doesn't fit Remington Model 887 (08/11/2012)

Works Great (19/09/2009)

This item works great and looks good too. Very nicely machined and finished.

Perfect Fit, Easily Installed (26/03/2011)

Exactly what I was looking for! (31/07/2018)

FNH SLP 18" 3" Magnum Police Shotguns (18/01/2010)

Although this is a great design and very good quality, it absolutely will not fit an FNH SLP shotgun magazine tube extention. FNH now makes a Tri-Rail extention. [...]

Didn't Work (09/02/2010)