Le verrou de culasse en acier a une partie inférieure agrandie pour un verrouillage facile à l'arrière.
La partie supérieure élargie permet une libération rapide du culasse.
Le pavé tactile « Diamond Texture » assure un engagement positif et améliore l'apparence de ton fusil.
Caractéristiques
Type d'arme:AR-15
Poids du colis:0,045kg
Hauteur d'expédition:25mm
Largeur d'expédition:69mm
Longueur d'expédition:198mm
UPC:811452029613
Détails de l'article
Fabriqué au USA
US export classification: 0A501.x
Spécifications:
Fabrication: AR-15
36.936.91EUR
36.9EUR036,90 €
Le prix inclut la TVA mais pas la livraison .
Référence: 100011243
N° fabr.: 011510057
811452029613 Le catch de bolt en acier possède une partie inférieure agrandie qui facilite le verrouillage du bolt à l'arrière. La partie supérieure agrandie permet un relâchement rapide du bolt, et le pad pour le pouce avec texture « Diamond » offre une prise sûre et améliore l'apparence du fusil.
Permet un Verrouillage Facile & un Relâchement Rapide du Bolt
Le catch de bolt en acier possède une partie inférieure agrandie qui facilite le verrouillage du bolt à l'arrière. La partie supérieure agrandie permet un relâchement rapide du bolt, et le pad pour le pouce avec texture « Diamond » offre une prise sûre et améliore l'apparence du fusil.
Enables Easy Locking & Fast Bolt Release
Steel bolt catch features an enlarged lower portion that makes it easy to lock bolt to the rear. Enlarged upper portion allows fast bolt release, and “Diamond Texture” thumb pad gives positive engagement and enhances rifle’s appearance.
Points forts
Le verrou de culasse en acier a une partie inférieure agrandie pour un verrouillage facile à l'arrière.
La partie supérieure élargie permet une libération rapide du culasse.
Le pavé tactile « Diamond Texture » assure un engagement positif et améliore l'apparence de ton fusil.
Caractéristiques
Type d'arme:AR-15
Poids du colis:0,045kg
Hauteur d'expédition:25mm
Largeur d'expédition:69mm
Longueur d'expédition:198mm
UPC:811452029613
Détails de l'article
Fabriqué au USA
US export classification: 0A501.x
Avis des clients
Notes des clients (9)
2,9 / 5
Non recommandé
Bent and locked up my 9mm carbine 30/07/2018
I've run a few of these before without issue, but on the FIRST time I ran my 9mm carbine to slide-lock it bent this piece and locked up my PCC HARD. I had to use a screwdriver and a hammer to bend it back enough to tap it down. I could then slide my bolt forward and begin to repair. I had been using a box-stock factory bolt catch without issue prior to this. Not an upgrade and too soft. The one I had on my HD rifle is now coming off as well and replaced with something hardened.
Moyennement recommandé
No go 22/12/2016
Love the feel of this catch, couldn't care about looks. I wanted a larger paddle and In return the bolt won't lock up on the last round. Happened after two months. I don't feel you should have to remove the paddle to clean it inside of 10000 rounds. And I find it funny that the stock catch never wore down on my service rifle.
Best uses..."target practice" only because this will make you one. Save your money and go stock!
Fortement recommandé
Great upgrade 17/03/2016
After my first carbine class I went in search of a bolt catch that had an enlarged bottom portion for locking the bolt open.
I found the Seekins and gave it a try. It worked perfectly and was exactly what I was looking for. Since then I've installed them in three other lowers and have had no problems with fit or function.
I've installed them in lowers from BCM, Spikes Tactical, and PSA.
Moyennement recommandé
Didn't work for me 02/02/2015
I've build around 11 ARs using Aero, Spikes, DPMS, Bushmaster and other lowers for myself and a few friends. I've always used the bolt catch from DPMS or CMMG lpk. On my last AR build (Aero lower) for myself I decided to put this item in for a more enhanced bolt catch. I wanted one bigger in both the catch and release areas.
Installation was like any bolt catch. It moved freely without the mag and it locked the bolt without the mag but when the mag came into play, it never locked itself. It seemed like it had problems moving, it felt tight with the mag in the mag well.
It looks good, good material, nice wide surface on both ends but not in spec.
Non recommandé
Out of Spec Hole Diameter 23/11/2014
I bought one of these about a year ago for the AR 15 that I was building and it worked perfectly. I decided to buy two more for my other AR's but they are both defective. The hole diameter is too small and they will not work freely. The hole diameter is the same size as the roll pin when it should be slightly larger. When I compared the hole sizes to the old bolt catch their is a very noticeable difference. I am guessing that they ran a whole batch of these with the wrong hole size and from the other review that I read Seekins Precision does not QA their parts! I think they need to remove the name "Precision" from their name since they say they make MIL SPEC parts when their parts aren't!
Moyennement recommandé
Out of spec 24/09/2014
I have tried two of the Seekins enhanced bolt catch on different builds without success.
The first one would not lock the bolt open after firing the last round from several different magazines, and would not hold the bolt back even when manually locked back.
The second one I ordered would not fit into the receiver at all. It was a Seekins forged lower that I was building up. I measured both the lower and the bolt catch and the bolt catch was slightly oversized to the point that it would not fit.
I really like the design of the larger paddle, but they need to get their specs correct on this part.
Used for a RRA Entry Tactical Duty Rifle. This simple upgrade makes it faster & easier to lock back and release the BCG. No Qualms Here Buy It! you wont regret it!
Recommandé
Will NOT work in Mega Side-Charging Upr 21/06/2014
While this is a lovely bolt catch, it will NOT work in a Mega Arms Side-Charging Upper. There is not enough material milled out of the upper for this bolt catch to fit.
Recommandé
Big upgrade over the stock part 20/05/2014
I was drawn to this part because I found the bottom portion of a standard bolt catch to be inadequate when locking the bolt open. The enlarged and protruded bottom portion of this part solved that problem for me. It is machined well and of high quality. The only reason I did not give it 5 stars is because it is incompatible with the Magpul BAD lever or any equivalent device that attaches to a standard bolt release. This may or may not matter to you.
Opérateur économique responsable conformément au règlement de l'UE
Brownells France
Immeuble l'Horizon 3 Rue Jacques Constant Milleret
42000 Saint-Étienne
France
contact@brownells.fr
Derniers visualisés
Oups ! Quelque chose s’est mal passé.
Nous avons rencontré une erreur lors du chargement de ce contenu. Veuillez actualiser la page pour continuer. Si le problème persiste, contactez notre service client.
Améliorez votre AR-15 avec le verrou de culasse SEEKINS PRECISION. 🔒 Conception ergonomique pour un relâchement rapide et un look stylé.
Ces articles sont contrôlés par le gouvernement des États-Unis et autorisés uniquement à être exportés vers le pays de destination finale pour être utilisés par le destinataire final ou les utilisateurs finaux identifiés dans le présent document. Ils ne peuvent être ni revendus, ni cédés à tout autre pays ou toute personne autre que le destinataire final autorisé ou l'utilisateur final, soit dans leur forme originale, soit après avoir été incorporés dans d'autres produits, sans l'accord préalable du gouvernement des États-Unis ou d'une autre manière autorisée par la législation américaine, règlements.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Ces articles sont contrôlés par le gouvernement des États-Unis et autorisés uniquement à être exportés vers le pays de destination finale pour être utilisés par le destinataire final ou les utilisateurs finaux identifiés dans le présent document. Ils ne peuvent être ni revendus, ni cédés à tout autre pays ou toute personne autre que le destinataire final autorisé ou l'utilisateur final, soit dans leur forme originale, soit après avoir été incorporés dans d'autres produits, sans l'accord préalable du gouvernement des États-Unis ou d'une autre manière autorisée par la législation américaine, règlements.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Les broches pivot et de démontage avec des têtes surdimensionnées permettent une séparation rapide des récepteurs.
Il suffit de saisir la tête de style bouton pour désengager la broche sans outils supplémentaires.
Usiné en acier trempé avec finition Parkerisée, cet ensemble est durable et conforme aux spécifications militaires.
Améliore la précision de votre AR-15 en éliminant le jeu entre le récepteur supérieur et inférieur.
Fabriqué en caoutchouc synthétique dense, il est facile à installer et économique.
Peut être taillé pour s'adapter à différentes variations d'ajustement.
Le bouton de largage en aluminium usiné offre une surface à « Texture Diamant » pour un meilleur grip.
Il s'adapte à tous les récepteurs inférieurs mil-spec, remplaçant facilement le bouton d'origine.
Fabriqué en aluminium 6061 T6, il est anodisé dur et disponible en noir mat.
Les ressorts à puissance réduite offrent une détente de 3,5 livres avec des détentes J.P. et de 4,5 à 5 livres avec des composants standard.
Inclut tous les ressorts nécessaires et des instructions pour polir la surface de contact pour une détente lisse.
Conçu uniquement pour un usage récréatif, ne pas utiliser dans des armes à feu de service ou de défense à domicile.