Votre panier est vide.

Panier

Aide et contact

Livraison standard gratuite pour les commandes de plus de 249 €

Politique de retour de 100 jours

Newsletter

Promotions

Plus de 300 000 clients - nous vous disons merci !

4,93/5 "Très bien" (1400+ avis)

40 000+ produits pour la chasse et le tir sportif

BROWNELLS
BRASS PILOTS

050806027534 080944400

Centre les outils pour un travail précis

Le pilote en acier trempé maintient les outils de fraisage et de chanfreinage correctement centrés dans le canon. Résiste à l'usure pendant des années de service.

Sélectionne l'un des éléments suivants pour d'autres canons de fusil/pistolet, outils de fraisage et de chanfreinage.

	Set en acier pour un calibre		Couteau à 45° & Pilote en acier
	Set en laiton pour un calibre		Couteau à 45° & Pilote en laiton
	Couteau à 90° & Pilote en acier		Pilote en acier uniquement
	Couteau à 90° & Pilote en laiton		Sets combinés de chanfreinage & fraisage

SPÉCIFICATIONS : Laiton. Longueur de 1¼" (3,2 cm). Pilotes .45 ACP - .45 ACP-1 convient aux modèles S&W 25 & 625. .45 ACP-2 convient au Colt 1917.

Plus...

Centers Cutters For Accurate Work

Hardened steel pilot keeps Facing and Chamfering cutters properly centered in the bore. Resists wear for years of service.

Select one of the following for other rifle/handgun muzzles, cylinder facing & chamfering tools.

	Steel One Caliber Set		45° Cutter & Steel Pilot
	Brass One Caliber Set		45° Cutter & Brass Pilot
	90° Cutter & Steel Pilot		Steel Pilot Only
	90° Cutter & Brass Pilot		Chamfering & Facing Combo Sets

SPECS: Brass. 1¼" (3.2cm) long. .45 ACP Pilots - .45 ACP-1 fits S&W model 25 & 625. .45 ACP-2 fits Colt 1917.

Plus...

Évaluations client de BROWNELLS .40/10MM MUZZLE BRASS PILOT

Nombre d'évaluations: 9
De brownells.com: 9
Note moyenne: 4

Will not fit .20 cal Sheridan air rifle (21/08/2018)

Just a heads up......This does not fit the muzzle of a .20 Sheridan air rifle unless you turn it down a few thousands on a lathe.

Brass pilot for .45 revolver, muzzle (04/06/2016)

Used this with Brownells 45 degree, 5/8" chamfer cutter (#080-588-625) to re-crown my S&W 625PC. The pilot measured .4405" diameter which was a good fit for my bore (.443") diameter. Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.

.357 BBL. Revolver Muzzle Brass Pilot (04/06/2016)

Used this with Brownells 45 degree, 5/8" chamfer cutter (#080-588-625) to re-crown my S&W 627PC & 686. The pilot measured .3445" diameter which was a good fit for my bore (.3455 & .3460") diameter. Purchase Brownells Facing & Chamfering Cutter Handle (#080-589-000) to use these together.

8mm brass pilot dose not fit (26/11/2011)

Too large to fit in muzzle of 8mm I have tried it in three 8x57 mausers and it dose not go in any of them.. I am going to turn it down so it will fit because it is too much of a pain to send back, but beware if you buy this it will not fit.

Perfect fit for 8mm Mauser (16/10/2015)

Very snug fit, as it should be.

Worked perfectly.

This is the one for Mosin Nagant 91/30 (16/12/2012)

Excellent product.

NOT the one for my 91/30 (14/04/2017)

A previous reviewer stated this is the one for the Mosin 91/30 so I bought it. It arrived with rifling marks pressed approx 1/32" into the end of it. Possibly someone purchased it for a Mosin 91/30 and attempted to force fit it. It is NOT for the Mosin. It fit in one of my M44's and my Type 53 but would not turn in either and would not fit my other M44 or 91/30 at all. I inserted it into my .303 Enfield and it feels a little loose. My dial calipers show the bore guide to be .301". I think it should be a bit larger in diameter for use in the 303 and am considering returning it or sanding it down to fit the Mosins.

Worked like a charm on my mosin nagant (01/06/2017)

I bought this even after being confused as if this would fit my 91/30 Mosin Nagant. Well, it fit perfectly and worked like a charm.

45 ACP-1 cylinder brass pilot (04/06/2016)

Ordered this to chamfer my 625PC 45ACP chamber openings/charge holes. The Q&A for the 45ACP-2 says the 45ACP-1 is the correct one for S&W 25/625. However, it does not fully fit in either my 625PC, or 325NG, cylinder openings to allow the 45 degree, 5/8" chamfer cutter to contact the cylinder. The pilot has two guide surfaces that measure: .4475" (throat) & .4775" (chamber). The throat end is fine. The chamber end is too large. My chambers measure .474" and .475" at the case ledge (where the case mouth headspaces on) and the pilot needs to be able to contact it to allow enough depth for the chamfer tool to make contact. Be aware it will have to be polished to a slightly smaller diameter to work in a S&W 625 45ACP chamber.

Lire 9 plus d'avis sur brownells.com

22.9 38.9 39 EUR

Référence: 080944400
BROWNELLS .40/10MM MUZZLE BRASS PILOT 050806027534 Le pilote en acier trempé maintient les outils de fraisage et de chanfreinage correctement centrés dans le canon. Résiste à l'usure pendant des années de service.

31.9 EUR 4 31,90 € *

Délai de livraison environ 14-21 jours.

Caractéristiques: Calibre: 40/10 mm (.400-.401) Matériau: Brass

BROWNELLS BRASS PILOTS

Évaluations client de BROWNELLS .40/10MM MUZZLE BRASS PILOT

Caractéristiques

Détails de l'article

Évaluations client de BROWNELLS .40/10MM MUZZLE BRASS PILOT

Se connecter

Méthodes de paiement sécurisées

Associations professionnelles

Bienvenue !

BROWNELLS
BRASS PILOTS