M-LOK INDEXER L'Indexer Arisaka est une continuation de nos accessoires de contrôle minimal et à profil bas. L'Indexer peut être utilisé de plusieurs manières, mais son intention principale est de le placer entre deux doigts (généralement l'index et le majeur). Cela le place généralement plus en avant sur le garde-main, ce qui signifie également qu'il ne gêne pas lors des transitions vers des positions de tir à genoux ou couché, où la plupart des gens déplacent leur main de soutien vers l'arrière. Utilisé de cette manière, l'Indexer rend beaucoup plus facile le tir du fusil contre ton épaule et le maintien du contrôle pendant le tir. De plus, le profil plus large et plat de l'Indexer fonctionne très bien comme un hand stop ou un barricade stop, et il sert également de limite avant pour empêcher tes doigts de glisser des garde-mains plus courts sur un canon chaud ou un suppresseur. KeyMod L'Indexer Arisaka en attente de brevet est une continuation de nos accessoires de contrôle minimal et à profil bas. Il a été développé en réponse à la demande des utilisateurs pour une version KeyMod de notre Finger Stop pour rails Picatinny, et présente un profil mince de l'avant vers l'arrière et un léger rayon sur les deux faces. Hauteur : 1,0" Largeur : 0,58" Longueur : 1,5" Poids : 0,6 oz L'Indexer est usiné CNC à partir d'aluminium 6061-T651 et anodisé en dur de type III MIL-A-8625. Nécessite une clé Torx T15 pour l'installation (non incluse). Matériel : Deux vis KeyMod inversées BCM. Geissele SMR 416 L'Indexer Arisaka en attente de brevet est une continuation de nos accessoires de contrôle minimal et à profil bas. Il a été développé en réponse à la demande des utilisateurs pour une version Geissele SMR 416 de notre Finger Stop pour rails Picatinny, et présente un profil mince de l'avant vers l'arrière et un léger rayon sur les deux faces. Hauteur : 1,0" Largeur : 0,58" Longueur : 2,2" Poids : 0,9 oz L'Indexer est usiné CNC à partir d'aluminium 6061-T651 et anodisé en dur de type III MIL-A-8625. Nécessite un tournevis IP25 TorxPlus pour l'installation (non inclus). Matériel : Deux vis Torx à tête plate 10-32x3/8". M-LOK L'Indexer Arisaka en attente de brevet est une continuation de nos accessoires de contrôle minimal et à profil bas. Il a été développé en réponse à la demande des utilisateurs pour une version M-Lok de notre Finger Stop pour rails Picatinny, et présente un profil mince de l'avant vers l'arrière et un léger rayon sur les deux faces. Hauteur : 1,0" Largeur : 0,58" Longueur : 1,5" Poids : 0,6 oz L'Indexer est usiné CNC à partir d'aluminium 6061-T651 et anodisé en dur de type III MIL-A-8625. Nécessite une clé Torx IP20/T20 pour l'installation (non incluse). Matériel : Deux écrous M-Lok et deux vis Torx à tête de bouton 10-24x5/16". Fabriqué aux États-Unis.
M-LOK INDEXER The Arisaka Indexer is a continuation of our low profile, minimal control accessories. The Indexer can be used in a variety of ways, but the main intent is to place it between two fingers (usually index and middle). This typically places it further forward on the handguard, which also means it doesn't get in the way when transitioning to kneeling or prone shooting positions, where most people move their support hand towards the rear. Used in this manner, the Indexer makes it much easier to pull the rifle into your shoulder and maintain control while shooting. Additionally, the wider, flatter profile of the Indexer functions very well as a hand stop or barricade stop, and also works as a forward limit to prevent your fingers from slipping off shorter handguards onto a hot barrel or suppressor. KeyMod The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for a KeyMod version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 1.5" Weight: 0.6 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires a T15 Torx wrench for installation (not included). Hardware: Two BCM inverted KeyMod screws. Geissele SMR 416 The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for a Geissele SMR 416 version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 2.2" Weight: 0.9 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP25 TorxPlus driver for installation (not included). Hardware: Two 10-32x3/8" Torx flat head screws. M-LOK The Patent Pending Arisaka Indexer is a continuation of our low profile, minimal control accessories. It was developed due to end-user demand for an M-Lok version of our Finger Stop for Picatinny rails, and features a slim front-to-back profile and slight radius across both faces. Height: 1.0" Width: 0.58" Length: 1.5" Weight: 0.6 oz The Indexer is CNC machined from 6061-T651 aluminum and MIL-A-8625 Type III hard coat anodized. Requires an IP20/T20 Torx wrench for installation (not included). Hardware: Two M-Lok nuts and two 10-24x5/16" Torx button head screws. Made in the USA.